GenCore Power Protection Insights

Blog

Trading kW Against Risk: A Cummins QSK / Perkins 4000 Spend Map for a Grain Terminal

Posted on Wednesday 17th of June 2026 by Rebecca Sloan

Cummins vs Perkins generator — A port grain terminal must keep its aeration fans and dust-suppression running through outages — a fire risk if it doesn't. [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

Cummins vs Perkins Generator: The Spec That Actually Fails First

Posted on Wednesday 17th of June 2026 by Rebecca Sloan

Cummins vs Perkins generator — COMMON BELIEF “The engine wears out first.” That’s the reflexive answer when a generator dies after ten years of weekly exercise. [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

Four Things Plant Engineers Get Wrong About 700 kW Cummins and Perkins Sets

Posted on Wednesday 17th of June 2026 by Rebecca Sloan

Cummins vs Perkins generator — An aggregates quarry needed standby for its primary crusher feed and weighbridge offices. The shortlist came down to a Cummins QSK-family set and a Perkins 4000-series set at the same ~700 kW. [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

"Why does my 1000 kW airport set keep failing the witnessed block-load test — and would the other brand pass?"

Posted on Wednesday 17th of June 2026 by Rebecca Sloan

Cummins vs Caterpillar generator — An airport's new standby set — feeding the airfield lighting regulators and the terminal's life-safety loads — keeps dipping too far on the witnessed step test. [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

The moment the compressors re-strike: which standby set trips first, and why the nameplate won't tell you

Posted on Wednesday 17th of June 2026 by Rebecca Sloan

Cummins vs Kohler-SDMO generator — A regional cold-storage distribution centre holds about 700 kW of refrigeration plant on its standby bus. [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

4 Numbers That Kill the “Maintenance-Light” Myth: Cummins vs SDMO Generator

Posted on Wednesday 17th of June 2026 by Rebecca Sloan

Cummins vs Kohler-SDMO generator — You hear it constantly: “Just buy a generator that doesn’t need much looking after.” That’s a myth — a dangerous one when you’re sizing a panel that’s supposed to run unattended. [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

5 Numbers That Decide the Cummins vs Caterpillar Generator Question — & Why Maintenance-Light Tips the Odds

Posted on Wednesday 17th of June 2026 by Rebecca Sloan

Cummins vs Caterpillar generator — Here’s the myth: “You buy Caterpillar when you never want it to fail.” True enough — a C32 at standby rating is a monument of endurance. [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

Declared, Undeclared, Inferred: Reading a Cummins QSK vs KOHLER-SDMO D830 Quote for an N+1 Data Hall

Posted on Wednesday 17th of June 2026 by Rebecca Sloan

Cummins vs Kohler-SDMO generator — A colocation operator building an N+1 standby plant for a single data hall asked for two like-for-like quotes: a Cummins QSK set in its lower band and a KOHLER-SDMO D830 (about 750 kW prime / 825 kVA standby),… [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

Cummins vs Caterpillar Generator: runtime under real load

Posted on Wednesday 17th of June 2026 by Rebecca Sloan

Cummins vs Caterpillar generator — “A Caterpillar generator runs longer on a full tank than a Cummins of similar rating.” This shows up in contractor circles and occasionally in tender notes — the idea that Cat iron has a lower specific fuel… [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

The Lifetime-Cost Myths Behind a 900 kW Cummins vs Caterpillar Choice at a Semiconductor Fab

Posted on Wednesday 17th of June 2026 by Rebecca Sloan

Cummins vs Caterpillar generator — A wafer fab cannot tolerate a process excursion from a power blip — a single bad transient can scrap a lot worth more than the genset. [...]

Continue Reading →

Posted in Blog

Leave a comment