GenCore Power Protection Insights

Blog

“Efficiency you can actually keep” — the eligibility gate between Cummins and SDMO diesel generators

Posted on Wednesday 17th of June 2026 by Rebecca Sloan

Cummins vs Kohler-SDMO generator — COST OF ERROR You pick a 250 kVA SDMO D275 because the brochure says 38.1 L/hr at 75% load. That number is real — but only if you wire the generator into a system that actually lets it run at 75% load factor. [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

"At 650 kW, does prime or standby rating decide my Cummins-vs-Perkins choice — or am I asking the wrong question?"

Posted on Wednesday 17th of June 2026 by Rebecca Sloan

Cummins vs Perkins generator — A district-heating plant operator wants one 650 kW set to backstop the circulation pumps and the gas boosters. The honest answer takes four stages, and the threshold only appears at the end. [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

3 Numbers That Decide When Your Generator Load Doubles – Cummins vs SDMO

Posted on Wednesday 17th of June 2026 by Rebecca Sloan

Cummins vs Kohler-SDMO generator — You sized the genset for a 150 kVA base load. Then the client adds a chiller, or a second production line, and suddenly the nameplate reads 300 kVA. [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

Cummins vs Perkins Generator: when the load doubles

Posted on Wednesday 17th of June 2026 by Rebecca Sloan

Cummins vs Perkins generator — You sized a generator for a 250 kW load. Then the plant adds another 250 kW line. The old unit either carries the double — or it drops. [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

Picking the 800 kW Set for a Broadcast Centre: A Cummins QSK vs Perkins 4000 Decision Path

Posted on Wednesday 17th of June 2026 by Rebecca Sloan

Cummins vs Perkins generator — A national broadcast playout facility cannot go dark for even one frame. Here is the order in which the mechanisms decide — at the ~800 kW band where Cummins QSK and Perkins 4000 genuinely overlap — and the… [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

Cummins vs Perkins Generator: the Noisy Feed That Doubles Your TCO

Posted on Wednesday 17th of June 2026 by Rebecca Sloan

Cummins vs Perkins generator — If you think a noisy generator feed is just an annoyance — something you can bury under a concrete pad or hope the neighbours don’t call the council — you’re already on the wrong side of the real cost. [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

Three Cases at 2 MW: Cummins QSK60 vs Caterpillar 3516 on a Utility Peaking Bus

Posted on Wednesday 17th of June 2026 by Rebecca Sloan

Cummins vs Caterpillar generator — A municipal utility builds a peaking and grid-support array around 2 MW per engine. Cummins QSK60 (2000 kW standby) and Caterpillar 3516 (1450–2500 kW) both land here. [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

How Big Is the Difference, Really? Cummins QSK vs KOHLER-SDMO D440 at a Wastewater Works

Posted on Wednesday 17th of June 2026 by Rebecca Sloan

Cummins vs Kohler-SDMO generator — A wastewater treatment works runs blowers, screw pumps and a SCADA room that cannot be allowed to flood when the grid drops. [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

Four Beliefs That Mis-Size a Hospital Standby Set: Cummins QSK vs KOHLER-SDMO D830 at 750 kW

Posted on Wednesday 17th of June 2026 by Rebecca Sloan

Cummins vs Kohler-SDMO generator — A 600-bed hospital needs a standby plant that can hold the essential-systems bus through a utility outage and a generator that the estates team can actually live with for twenty years. [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

“But the spec sheet says 275 kVA” — the one number that predicts which generator fails first

Posted on Wednesday 17th of June 2026 by Rebecca Sloan

Cummins vs Kohler-SDMO generator — Every buyer compares kW and kVA. That’s table stakes. The real split — the spec that actually decides whether your generator meets load or drops you into a blackout — is transient response, specifically ISO… [...]

Continue Reading →

Posted in Blog

Leave a comment