GenCore Power Protection Insights

Blog

5 Numbers That Decide the Cummins vs Caterpillar Generator Question — & Why Maintenance-Light Tips the Odds

Posted on Wednesday 17th of June 2026 by Jane Smith

Cummins vs Caterpillar generator — Here’s the myth: “You buy Caterpillar when you never want it to fail.” True enough — a C32 at standby rating is a monument of endurance. [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

Declared, Undeclared, Inferred: Reading a Cummins QSK vs KOHLER-SDMO D830 Quote for an N+1 Data Hall

Posted on Wednesday 17th of June 2026 by Jane Smith

Cummins vs Kohler-SDMO generator — A colocation operator building an N+1 standby plant for a single data hall asked for two like-for-like quotes: a Cummins QSK set in its lower band and a KOHLER-SDMO D830 (about 750 kW prime / 825 kVA standby),… [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

Cummins vs Caterpillar Generator: runtime under real load

Posted on Wednesday 17th of June 2026 by Jane Smith

Cummins vs Caterpillar generator — “A Caterpillar generator runs longer on a full tank than a Cummins of similar rating.” This shows up in contractor circles and occasionally in tender notes — the idea that Cat iron has a lower specific fuel… [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

The Lifetime-Cost Myths Behind a 900 kW Cummins vs Caterpillar Choice at a Semiconductor Fab

Posted on Wednesday 17th of June 2026 by Jane Smith

Cummins vs Caterpillar generator — A wafer fab cannot tolerate a process excursion from a power blip — a single bad transient can scrap a lot worth more than the genset. [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

“Efficiency you can actually keep” — the eligibility gate between Cummins and SDMO diesel generators

Posted on Wednesday 17th of June 2026 by Jane Smith

Cummins vs Kohler-SDMO generator — COST OF ERROR You pick a 250 kVA SDMO D275 because the brochure says 38.1 L/hr at 75% load. That number is real — but only if you wire the generator into a system that actually lets it run at 75% load factor. [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

"At 650 kW, does prime or standby rating decide my Cummins-vs-Perkins choice — or am I asking the wrong question?"

Posted on Wednesday 17th of June 2026 by Jane Smith

Cummins vs Perkins generator — A district-heating plant operator wants one 650 kW set to backstop the circulation pumps and the gas boosters. The honest answer takes four stages, and the threshold only appears at the end. [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

3 Numbers That Decide When Your Generator Load Doubles – Cummins vs SDMO

Posted on Wednesday 17th of June 2026 by Jane Smith

Cummins vs Kohler-SDMO generator — You sized the genset for a 150 kVA base load. Then the client adds a chiller, or a second production line, and suddenly the nameplate reads 300 kVA. [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

Cummins vs Perkins Generator: when the load doubles

Posted on Wednesday 17th of June 2026 by Jane Smith

Cummins vs Perkins generator — You sized a generator for a 250 kW load. Then the plant adds another 250 kW line. The old unit either carries the double — or it drops. [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

Picking the 800 kW Set for a Broadcast Centre: A Cummins QSK vs Perkins 4000 Decision Path

Posted on Wednesday 17th of June 2026 by Jane Smith

Cummins vs Perkins generator — A national broadcast playout facility cannot go dark for even one frame. Here is the order in which the mechanisms decide — at the ~800 kW band where Cummins QSK and Perkins 4000 genuinely overlap — and the… [...]

Continue Reading →

Posted in Blog

Leave a comment

Blog

Cummins vs Perkins Generator: the Noisy Feed That Doubles Your TCO

Posted on Wednesday 17th of June 2026 by Jane Smith

Cummins vs Perkins generator — If you think a noisy generator feed is just an annoyance — something you can bury under a concrete pad or hope the neighbours don’t call the council — you’re already on the wrong side of the real cost. [...]

Continue Reading →

Posted in Blog

Leave a comment